Ge-industrial-solutions CR460 LIGHTING CONTACTOR SERIES Manuel d'utilisateur télécharger pdf

HAZARDOUS VOLTAGE

Disconnect all power before working on equipment.

Electrical shock will cause severe injury or death.

TENSION DANGEREUSE

Coupez l’alimentation avant travailler sur le produit.

Electrocution peut causer de severes blessures ou la mort.

Description

The GE CR460 Series is a magnetically operated lighting

contactor, and is available in either an open or an enclosed

form. These contactors are field configurable for up to twelve

poles, with a maximum of eight normally closed “NC” poles.

Figure – 1 Mechanically Held Contactor

1 MAIN BASE

1.1 Description

The base of the lighting contactor (see Figure 1) has provisions

to accept power poles at positions “1” to “6”. Provisions are

also provided for up to 2 “NO” and 2 “NC” auxiliary contacts.

1.2 Installation

1. Remove all packing material from the base and all the kits.

2. Contactor must be mounted in the vertical position on a

sturdy support.

3. Additional over-current protection may be required. Refer

to the National Electrical Code or local electrical code as

required.

4. Refer to Table D on page 3 for the wire size and the

required torque for the coil terminals.

2 POWER POLES: CR460XP31 / 32

2.1 Description

Power poles are available in both single pole (CR460XP31)

and double pole (CR460XP32) versions. A maximum of

twelve poles may be installed on the base. Positions “1” to “4”

on the base can be configured as either normally open “NO” or

“NC” while positions “5” and “6” can be configured as “NO”

only.

2.2 Removal and Conversion of Power Poles

1. If installed ensure that all power is disconnected.

2. For multiple possible configurations of the power pole,

refer to the Table A below.

Table A

3. Remove block by pulling the clip as shown (see Figure 2).

Rotate block 180 degrees to convert from NO to NC.

Figure – 2

2.3 Installation of Power Poles

1. Check moving carrier to assure free movement

2. Install the block by sliding foot into slot; pull the clip, and

position block onto base. Release the clip.

DEH-40460 Instruction Sheet

WARNING !

CR460 LIGHTING CONTACTOR SERIES

GE Lighting Contactors

# of NC Contacts desired (3)

0 1 2 3 4 5 6 7 8

0 20 30 40 50 60 70 80

1 11 30 31 50 51 70 71 90

2 20 30 40 50 60 70 80 90 B0

3 30 31 50 51 70 71 90 91 CO

4 40 50 60 70 80 90 B0 C0 D0

5 50 51 70 71 90 91 C0

6 60 70 80 90 B0 C0 D0

7 70 71 90 91 CO

8 80 90 B0 CO D0

9 90 91 CO

10 B0 CO DO

11 C0

12 D0

# of NO Contacts desired (4) Standard Catalog # Digits

CR463L70AJA0

Main Base

NO Aux.

Contact

NC Aux.

Contact

1 2 3 4

Résumé du contenu

Page 1 - GE Lighting Contactors

1g HAZARDOUS VOLTAGEDisconnect all power before working on equipment.Electrical shock will cause severe injury or death.TENSION DANGEREUSECoupez l’ali

Page 2

23. Check for the lettering on the base. “NO” should bevisible if the power pole is assembled as normally open, or“NC”, if it is assembled a normally

Page 3

3Figure – 65 COIL KITS5.1 DescriptionA wide range of coils is available for both electrically held andmechanically held lighting contactor. Refer to

Page 4 - GE Industrial Systems

4Wiring DiagramsCR460L Electrically Held ContactorCR460M Mechanically Held Contactorg

Commentaires sur ces manuels

Pas de commentaire

Ge-industrial-solutions CR460 LIGHTING CONTACTOR SERIES Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Ge-industrial-solutions CR460 LIGHTING CONTACTOR SERIES. GE Industrial Solutions CR460 LIGHTING CONTACTOR SERIES User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Ge-industrial-solutions CR460 LIGHTING CONTACTOR SERIES