Ge-industrial-solutions AF-600 FP Apogee_FLN Manuel d'utilisateur

GE Consumer & IndustrialElectrical DistributionAF-600 FPTMApogee/FLNOperating InstructionsThe instructions do not purport to cover all details or

The PID controller in the drive supports two feedback values and two setpoints. The feedback can be received in the form of network bus signals and/or

AF-600 FP Apogee FLN Operating Instructions103

3 Drive Network StrategiesThe drive has its own internal PID closed loop controller. This can be turned on or off, depending on the requirements of th

28 CMD COAST In most cases, it is necessary to set this point to [NO] to make the drive run. If this is set to [COAST] while thedrive is running, the

Network inputs to the frequency converter:In addition to start/stop control, which was discussed in Strategy Two, the FLN provides the frequency conve

AF-600 FP Apogee FLN Operating Instructions144

4 Drive Special Functions4.1.1 Special FunctionsIn addition to the control strategies described above, the drive provides additional control flexibili

AF-600 FP Apogee FLN Operating Instructions165

5Network Connection5.1.1 Network ConnectionConnect the frequency converter to the RS-485 network as follows (see also diagram):1. Connect signal wires

AF-600 FP Apogee FLN Operating Instructions186

Contents1 Introduction3Safety 3Introduction 4About this Manual 4Assumptions 4HP/kW Conversion 52 Drive Functional Features7Drive Operation (F-64) 7Mot

6 Parameters6.1.1 Parameter SettingsThe frequency converter has a unique FLN address, which is transmitted over the RS-485 serial bus. The network wil

AF-600 FP Apogee FLN Operating Instructions207

7 Start-up and Troubleshooting7.1 Start-up7.1.1 Start-up of FLN ControlThis procedure assumes that the frequency converter has been installed properly

1. By using the [RESET] control button on the Keypad.2. Via a digital input with the “Reset” function.3. Via serial communication/optional network.4.

No. Description Warning Alarm/Trip Alarm/Trip Lock Parameter Reference1 10 Volts low X 2 Live zero error (X) (X) par. AN-01 Live Zero Time-out

No. Description Warning Alarm/Trip Alarm/Trip Lock Parameter Reference200 Fire Mode X FB-0#201 Fire Mode was Active X K-7#202 Fire Mode Limits

Pointno.6000pointno.DescriptorFactorydefault(SI)Engr.Unit(SI)Slope(SI)Intercept(SI)OntextOfftextRangeMaxvaue(SI)Minvalue(SI)PointtypeClassType(Note 1)

Pointno.6000pointno.DescriptorFactorydefault(SI)Engr.Unit(SI)Slope(SI)Intercept(SI)OntextOfftextRangeMaxvaue(SI)Minvalue(SI)PointtypeClassTypeReadOnly

Pointno.6000pointno.DescriptorFactorydefault(SI)Engr.Unit(SI)Slope(SI)Intercept(SI)OntextOfftextRangeMaxvaue(SI)Minvalue(SI)PointtypeClassTypeReadOnly

Pointno.6000pointno.DescriptorFactorydefault(SI)Engr.Unit(SI)Slope(SI)Intercept(SI)OntextOfftextRangeMaxvaue(SI)Minvalue(SI)PointtypeClassTypeReadOnly

6 Parameters19Parameter Settings 197 Start-up and Troubleshooting21Start-up 21Start-up of FLN Control 21Troubleshooting 21Faults, Warnings and Alarms

Pointno.6000pointno.DescriptorFactorydefault(SI)Engr.Unit(SI)Slope(SI)Intercept(SI)OntextOfftextRangeMaxvaue(SI)Minvalue(SI)PointtypeClassTypeReadOnly

7.3 Start-up7.3.1 Start-up of FLN ControlThis procedure assumes that the frequency converter has been installed properly and is operational in Hand co

GE Consumer & IndustrialElectrical DistributionAF-600 FPTMApogee/FLNOperating InstructionsThe instructions do not purport to cover all details or

1Introduction1.1.1 SafetyRotating shafts and electrical equipment can be hazardous. Therefore, it is strongly recommended that all electrical work con

1.2.1 IntroductionThe Siemens Floor Level Network (FLN) is a master/ slave control network for serial communication with various control devices. The

1.2.5 Abbreviations and Standards Abbreviations: Terms: SI-units: I-P units:a Accelerationm/s2ft/s2AWG American wire gauge Auto Tune Automatic Moto

AF-600 FP Apogee FLN Operating Instructions62

2 Drive Functional FeaturesThe FLN protocol built into the drive frequency converter allows programming of numerous features and monitoring of the dri

2.1.8 Freeze Mode (25, 26)If desired, the frequency of the drive can be frozen at its present value. The mode is indicated by data point 25. It is an