Series
Lighting Control Panel boards
DEH41095 Installation Instructions R02
WARNING: Danger of electrical shock or injury. Turn OFF power service to the line side of the panel
board or switchboard before working inside the equipment or removing any component. Equipment
is to be installed and maintained b
ro
erl
trained and
ualified
ersonnel onl
.
Replacement of Controller
Transformer
Secondar
wires
Power in
terminal at
Controller
FIG 1
Catalog No. Qty. Description
SRGLCTDP 1 Controller with out Ethernet
SRGLCTDP
1 Controller with Ethernet
Removal of Controller:
1. Ensure that the Installer is properly grounded while handling
Controller
2. Remove the front cover & dead front of the Panel board
Integrated Switchboard.
3. Lift up to unplug the Power in terminal at controller see fig 1. Also
disconnect all the communication ports such as ethernet etc to
the controller.
4. Unscrew the DB25 connector screws & remove the DB25
connector cable ends at the controller box sides (both sides).
5. Unscrew the controller cover mtg screws (qty-2) and lift the
controller cover upwards.
6. Unscrew the hold down bracket screws and remove the hold
down brackets from both sides of controller box.
7. Remove the Caplugs on the controller box (qty-4)
8. Unscrew the Controller board supports mtg screws (qty-2)
9. Unscrew the Ground stud screws (qty-3 )
10. Pull back and lift the controller assembly along with the controlle
board supports.
11. Pull off the controller board supports (qty-2) side ways and save
for new controller.
Reinstallation Instructions:
1. Push on the saved controller board supports (qty-2) onto each
end of new controller.
2. Drop this assembly along with the controller board supports at an
inclination and push forward in the controller box so as to have
proper seating (ensure that the hooks provided on the controlle
board supports locks in the controller box).
3. Tighten the ground stud screws (qty-3) so as to hold the controlle
board firmly to the controller box. Torque to 10 lb-inch.
4. Tighten the controller board support mtg screws (qty-2) to torque
of 15-20 lb inch
5. Push In all the Caplugs in to the controller box.
6. Drop down the controller cover in to the mtg holes provided in the
box and other end of the controller cover to seat in the controlle
board support recess grooves.
7. Tighten the controller cover mtg screws to torque of 15-20 lb-inch.
8. Assemble the hold down bracket both sides and tighten it to the
box with the hold down bracket screws to torque of 15-20 lb-inch.
9. Push the ends of the DB25 connector cable ends to the controlle
connector both sides and tighten the knurled screws at end o
each cable connector to torque of 5 Lb-inch.
10. Plug in the transformer secondary wire connector to Power in
terminal on controller.
11. Connect all the communication port wires such as ethernet etc to
the controller.
12. Install dead front and front cover of the panel board / Integrated
switchboard.
Recessed
groove
DB25 Connector
Ca
le
Controller
Box
Controller
Board support
mtg screws
Caplugs
Hold Down
Bracket
Hold Down
racket mt
screw
Controller
ASRGLCTDP
ASRGLCTDPE
Ground stud
screws
Controller Board
Su
ort
Controller
Cove
Controller cover
mt
screws
GE Consumer & Industrial General Electric Company, Plainville, CT 06062
2004 General Electric Company DEH41095 R02
(54 pages)
(4 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels