Ge-industrial-solutions 6KCV301PDP33 Profibus - DP Bus for AV300i Manuel d'utilisateur

GE Industrial Control SystemsGE Industrial Control SystemsINSTRUCTIONS6KCV301PDP33Profibus - DP Bus for AV300iTM

—————— HARDWARE DESCRIPTION ——————210GEI-1004222.5 TECHNICAL SPECIFICATIONStorage temperature: -20°... +70°C (-68...+158°F)Operating temperature:

211—————— HARDWARE DESCRIPTION ——————Profibus-DPGndVccGndVcc6KCV301PDP33 6KCV301PDP33S2-2S2-1XS1/XS2390 ohm150 ohmXS1/XS2 S2-2S2-1390 ohm390 ohm150 o

313—————— BYTE ASSIGNMENT ——————Profibus-DP3.0 BYTES ASSIGNMENT FOR DATA EXCHANGEThe 6KCV301PDP33 card uses a 16-byte frame. The first 8 bytes re

—————— BYTE ASSIGNMENT ——————314GEI-100422B ) Data frame from Slave to Master:1 ) Data / ErrorThe content of this field depends on the kind of servic

315—————— BYTE ASSIGNMENT ——————Profibus-DP3.1 CONTROL BYTE SETTING76543210ServiceBitMeaning210000No request communications0 0 1 Drive parameter

—————— BYTE ASSIGNMENT ——————316GEI-1004223.2 MEANING OF HANDSHAKEThe Handshake bit prevents the same service request from being carried outmore th

317—————— BYTE ASSIGNMENT ——————Profibus-DP3.3 EXAMPLE OF DRIVE PARAMETER ACCESSThese example are referred to the AV300i drive software version 1

—————— BYTE ASSIGNMENT ——————318GEI-1004223.3.2 Drive parameter readingThe Actual speed parameter of the AV300i drive (software version 1.X) mustbe

419————— PROCESS DATA CHANNEL CONTROL ———Profibus-DP4.0 PROCESS DATA CHANNEL CONTROLThis function allows the assignment of the drive parameter to th

These instructions do not purport to cover all details or variations in equipment, nor toprovide every possible contingency to be met during installat

————— PROCESS DATA CHANNEL CONTROL ———420GEI-100422Operating modes:PDC Input channelPDC Input memoryPDC Output memoryPDC Output channelsb3_4020012301

421————— PROCESS DATA CHANNEL CONTROL ———Profibus-DPInput data descriptor of the Process Data Channel:PDC Input configuration202Ah8234 dec001 Word

523—————— ALARMS ——————Profibus-DP5.0 ALARMS5.1 PROFIBUS-DP ALARMSThe alarms indicated to the drive by the 6KCV301PDP33 card are the following:1 -

625———— VIRTUAL DIGIT INPUT OUTPUT CONTROL ———Profibus-DP6.0 VIRTUAL DIGITAL INPUT/OUTPUT CONTROLVirtual digital I/O are descrete signals which can b

727—————— KEYBOARD INTERFACE ——————Profibus-DP7.0 KEYBOARD INTERFACE7.1 MAIN MENU STRUCTUREThis structure appears when the Enter key is pressed and

—————— KEYBOARD INTERFACE ——————728GEI-1004227.2 6KCV301PDP33 INFO MenuThis Menu is used to display various information about the 6KCV301PDP33card; a

829—————— IDENTIFICATION CODES ——————Profibus-DP8.0 IDENTIFICATION CODES8.1 CARD IDENTIFICATION NUMBERThe Profibus-DP protocol requires an identi

Profibus-DPIII—————— TABLE OF CONTENTS ——————TABLE OF CONTENTS1.0 INTRODUCTION ... 51

931—————— MISCELLANEOUS ——————Profibus-DP9. MISCELLANEOUS9.1 GLOSSARY- Master PLC or PC device controlling the Profibus-DP; it has the right to acce

MANUALE 6KCV301PDP33 (2/99)Rev. 0.0 - 11.2.99GE Industrial Control SystemsWe bring good things to life.GEI-100422 Rev. 0.0 (2/99)Internet Address: htt

GEI-100422—————— TABLE OF CONTENTS ——————IV9. MISCELLANEOUS ... 319.1 GLOSSARY ...

15—————— INTRODUCTION ——————Profibus-DP1.0 INTRODUCTIONThis manual describes the 6KCV301PDP33 optional card for connecting ofinverters to Profib

—————— INTRODUCTION ——————16GEI-100422The total cycle time depends on the number of Slaves connected; the 1.5-Mbit/s Baud Rate allows 8 SIEI drives

27—————— HARDWARE DESCRIPTION ——————Profibus-DP2.0 HARDWARE DESCRIPTION2.1 DIMENSIONS, WEIGHT, DEGREE OF PROTECTIONXS1 XS2+5V RST DEA+5VESBI-PDP-33LH

—————— HARDWARE DESCRIPTION ——————28GEI-1004222.2 MOUNTINGThe 6KCV301PDP33 card is supplied with standoffs, screws, washers and a6KCV301PDP33-Drive

29—————— HARDWARE DESCRIPTION ——————Profibus-DP3. The 6KCV301PDP33-Drive link cable is connected to the XT connectoron the 6KCV301PDP33-card.4. The