Ge-industrial-solutions Spectra Series Power Panelboards AMC6EY and AMC6QB Manuel d'utilisateur télécharger pdf

Spectra Series™ Power Panelboards

Circuit Breakers and Modules

WARNING: Dan

er of electrical shock or in

Turn

OFF

ower ahead of the

anelboard or

switchboard before workin

inside the

ment or removin

com

onent. Do

not remove circuit

rotective devices or an

other com

onent until the

ower is turned

OFF.

General

These instructions apply to the following catalog numbers:

• Circuit breaker modules AMC6EY and AMC6QB

• Circuit breaker frames TEY, THQB, and THHQB

Installation

1. Prepare the module. Attach the filler supports to each

end of the module using the #10-32

/4" hex-head

screws, as shown in Figure 1. Tighten the screws to

15–20 in.-lbs. Loosen the latch-locking screws.

2. Install the circuit breaker(s). Hook the load end of the

circuit breaker onto the module and secure with the

captive screws on the line end, as shown in Figure 1.

Tighten the screws to 25 in.-lbs.

3. Install the module. Fully retract the latches on the end

of the module, shown in Figure 1, and hook one side

of the module on the interior rail. Release the latch.

Pivot the module onto the bussing and engage the

second latch. Release the latch. Tighten the latch

screws to 25 in.-lbs., as shown in Figure 2.

Figure 1. Installing the circuit breaker on the module.

Figure 2. Attaching the circuit breaker module to the panelboard

interior.

4. Wire the circuits. Refer to the rating label on the

circuit breaker for the proper tightening torques.

5. Filler plate kits. Install the appropriate filler plate kit

as listed in Table 1.

Breaker Module Filler Plate Kit

AMC6EY AFP3EYD

AMC6QB AFP3QBD

Table 1. Filler plate kit for each breaker module type.

Attention – Procedure for Aluminum

Terminations

1. Strip the insulation, being careful to not nick the wire.

2. Clean the wire strands with a wire brush.

3. Thoroughly coat the stripped conductor with a

suitable antioxidant compound, such as ALNOX or

PENETROX A13.

4. Insert the conductor and tighten the connector screw

to the torque indicated on the rating label.

GEH5677 Installation Instructions R03

Circuit

Breaker

Filler

Support

#10-32

Screw

Filler

Support

Load-End

Connection

Captive

Screws

Latch

Screw

Latch

Screw

Latch

1 2

Installation 1
GE Industrial Systems 2

Résumé du contenu

Page 1 - Installation

gSpectra Series™ Power PanelboardsCircuit Breakers and ModulesWARNING: Danger of electrical shock or injury.Turn OFF power ahead of the panelboard

Page 2 - GE Industrial Systems

gGE Industrial Systems General E

Plus de documents pour Équipement Ge-industrial-solutions Spectra Series Power Panelboards AMC6EY and AMC6QB

Voir le document Ge-industrial-solutions Spectra Series Power Panelboards AMC6EY and AMC6QB Manuel d'utilisateur

Ge-industrial-solutions Spectra Series Power Panelboards AMC6EY and AMC6QB Manuel d'utilisateur (2 pages)

Commentaires sur ces manuels

Pas de commentaire

Ge-industrial-solutions Spectra Series Power Panelboards AMC6EY and AMC6QB Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Ge-industrial-solutions Spectra Series Power Panelboards AMC6EY and AMC6QB. GE Industrial Solutions Spectra Series Power Panelboards AMC6EY and AMC6QB User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Équipement Ge-industrial-solutions Spectra Series Power Panelboards AMC6EY and AMC6QB

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Ge-industrial-solutions Spectra Series Power Panelboards AMC6EY and AMC6QB